Views: 14 Author: Site Editor Publish Time: 2024-05-03 Origin: Site
注意:
1.请确保文中的激光器图示与您使用的激光器为同一型号 本文适用 YLR-1000/1500-K 型号
2.如激光器厂家信号更改,则下列接线失效,请按照厂家提供的定义接线
3.请务必确认激光器使能.PWM的电压,如需5V则外接5V开关电源,本文使用了5V开关电源
4.请务必确认激光器的模拟量电压,控制板默认输出0-10V,如需0-4V请打开控制盒更改跳帽J7
Attention:
1. Please ensure that the laser icon in the article is the same model as the laser you are using. This article applies to YLR-1000/1500-K model
2. If the laser manufacturer's signal changes, the following wiring fails. Please connect the wiring according to the manufacturer's definition
3. Ensure that the laser is enabled. PWM voltage, if you need 5V then external 5V switching power supply, this paper uses 5V switching power supply
4. Be sure to confirm the analog voltage of the laser. The default output of the control board is 0-10V. If 0-4V is required, open the control box and change the jump cap J7
YLR-1000/1500-K 光纤激光器图示①
Figure 1 shows the YLR-1000/1500-K fiber laser
接线逻辑
Wiring logic
1.首先短接图①端子INTERLCOK中的【5/6】【9/10】【11/12】三组信号(线序从左到右1-12)
2.其中【7/8】使用触点按钮START接常开脚
1. First short-circuit [5/6] [9/10] [11/12] three groups of signals (line sequence from left to right 1-12) in the diagram ① terminal INTERLCOK.
2. Where [7/8] use the contact button START to connect the normal opening pin
3.INTERLFACE端子接线,提供模拟量,使能,PWM信号,因机型特殊,需要使用5V电源
3.INTERLFACE terminal wiring, provide analog, enable, PWM signal, because of the special model, need to use 5V power supply
激光器的7/21脚一起接5V电源的+提供使能和红光信号,但由于是上升沿触发,所以中间使用带锁的按钮接常开脚
激光器的8号脚接控制盒的信号接口三的5脚提供模拟量,但由于本机型是0-4V,所以务必在主板跳线(J7处的跳帽)
激光器的9号脚为公用地,接控制盒的4号脚并且连5V电源的-提供所有的参考地
4.开机顺序
激光器上电--按下触点按钮--按下带锁按钮-正常焊接
附件状态参考
The 7/21 pin of the laser is connected to the + of the 5V power supply to provide enable and red light signals, but because it is triggered by the rising edge, a lock button is used in the middle to connect the normal opening pin
Pin 8 of the laser is connected to pin 5 of signal interface 3 of the control box to provide analog, but because this model is 0-4V, it must be in the motherboard jumper (jump cap at J7).
The No. 9 foot of the laser is the public land, connected to the No. 4 foot of the control box and connected to the 5V power supply - provides all the reference ground
4. Boot sequence
Power on the laser - press the contact button - press the lock button - normal welding
Attachment status reference